CentOS7 ifconfig Command not found

Linux/Shell 2014-08-28 CentOS7,ifconfig, 网络配置

CentOS7刚发布,我忍不住把DELL T410从CentOS6升级到CentOS7。好不容易等安装结束后,立即配置网络,然后在yum源上安装环境。可是执行ifconfig的时候系统提示让我傻了眼:

[root@chaoge ~]# ifconfig
-bash: ifconfig: 未找到命令

这可是新安装的系统,怎么会没找到熟悉ifconfig命令呢?网上搜一下,一大堆人都在说是环境变量问题,但我确信我的/etc/profile设置是对的,于是终于找到一篇文章说是安装下net-tools就好

[root@chaoge ~]# yum install net-tools
已加载插件:fastestmirror
Repository base is listed more than once in the configuration
Repository updates is listed more than once in the configuration
Repository extras is listed more than once in the configuration
Repository centosplus is listed more than once in the configuration
Repository contrib is listed more than once in the configuration
base                                                                                                                                                                                           | 3.6 kB  00:00:00     
extras                                                                                                                                                                                         | 3.3 kB  00:00:00     
updates                                                                                                                                                                                        | 3.4 kB  00:00:00     
updates/7/x86_64/primary_db                                                                                                                                                                    | 2.8 MB  00:00:08     
Determining fastest mirrors
软件包 net-tools-2.0-0.17.20131004git.el7.x86_64 已安装并且是最新版本
无须任何处理

因为我已安装过net-tools所以提示我已经安装,现在熟悉的ifconfig又回来了

[root@chaoge ~]# ifconfig
em2: flags=4099<UP,BROADCAST,MULTICAST>  mtu 1500
        ether 78:2b:cb:41:9a:03  txqueuelen 1000  (Ethernet)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
        inet 192.168.1.48  netmask 255.255.255.0  broadcast 192.168.1.255
        inet6 fe80::7a2b:cbff:fe41:9a02  prefixlen 64  scopeid 0x20<link>
        ether 78:2b:cb:41:9a:02  txqueuelen 1000  (Ethernet)
        RX packets 82668  bytes 7831470 (7.4 MiB)
        RX errors 0  dropped 153388  overruns 0  frame 0
        TX packets 1276  bytes 204913 (200.1 KiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

lo: flags=73<UP,LOOPBACK,RUNNING>  mtu 65536
        inet 127.0.0.1  netmask 255.0.0.0
        inet6 ::1  prefixlen 128  scopeid 0x10<host>
        loop  txqueuelen 0  (Local Loopback)
        RX packets 12  bytes 1071 (1.0 KiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 12  bytes 1071 (1.0 KiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

 

文字链接:《CentOS7 ifconfig Command not found

文章地址:http://www.qttc.me/201408444.html

除非标注,琼台博客所有博文均为原创,转载请加文字链接注明来源

乳名?小名?昵称?网名?均可

email,放心,我不会给你乱投广告的

想获得回访就把你的站点URL写上(没有留空)

[NOTICE]木要投放广告
[NOTICE]木要骂人,说不该说的话
[NOTICE]自由言论,但要遵纪守法

Comments 0

    Hi,你想第一个做沙发么?